3D-блог:
инженеру на заметку

Geometric markers for 3D scanning: what they are, why you need them and how to use them

Volumetric marker holders: when you need them, how to place them and how to build a set.

Geometric markers for 3D scanning are volumetric reference objects placed on a part or next to it. Most often the term means small holders with markers on several faces: pyramids, prisms, cubes and towers. They let you place markers at different angles so the scanner can see them as the viewing angle changes.

Volumetric elements can also be used without stickers, as extra shape features for registering scans by geometry. This is a different mode: the scanner relies not on markers but on the surface of the elements themselves.

Below we look at how these approaches differ, when volumetric markers help, how to place them, how to build a set yourself or buy a ready-made one, and what to consider so that markers help instead of spoiling the scan. How to choose the markers themselves, where to stick them and how to check the layout is covered in a separate article, “Markers for 3D scanning: how to choose and place them correctly”.

For any 3D scanner the choice of reference objects depends on the equipment type and the task. Our RangeVision Spectrum, for example, can do without markers at all if the object has pronounced, non-repeating geometry, while Helix simply needs markers: without them it cannot orient itself in space. In both cases volumetric holders solve the same problem: to place markers where stickers directly on the part are inconvenient or poorly visible from the working directions.

Geometric markers in brief

  • In marker mode a volumetric holder helps place stickers at different angles on its faces.
  • In geometry-based registration an extra element can work by its shape alone, without stickers.
  • Ordinary flat markers are perfectly suitable for scanning too. Volumetric holders are needed when they help keep the reference points visible and conveniently placed.
  • When printing holders yourself, print only the body; buy round markers ready-made. 3D printing delivers neither a repeatable shape of the round area nor a stable retroreflective part, and many scanners expect exactly retroreflective markers.
  • A magnet in the base makes the holder removable: put it on, take it off, move it to the next object, snap it to a steel table. Most open models come down to exactly this.
  • If the only goal is to vary the surface geometry, printing is optional: plasticine or removable adhesive putty will do.
  • A holder must not cover the surfaces that have to be digitised or measured, and must not change position relative to the part during scanning.

What a volumetric marker is and how it differs from a marker

A marker is a reference the scanner recognises, most often a round sticker with contrasting areas. How markers of different types are built and which diameters are used is covered in the article about choosing and placing markers.
A volumetric holder is a body with markers placed on its faces. By itself it does not turn a single sticker into a reference visible from all sides. Its job is to place several markers so that part of them stays available to the cameras as the angle changes.
An auxiliary geometric element is an object whose shape is used to register scans by geometry. A boss fixed on a smooth part, for example, can add a distinguishable feature where there was none. The clearest example is adding extra geometry to a car hood or door so that neither the operator nor the algorithm struggles when the scans are merged.
In this article both kinds of volumetric reference objects are called geometric markers. But they have to be chosen and applied according to what the scanner actually uses: markers or surface geometry.
On the left, holders without stickers; on the right, ordinary round markers
On the left, holders without stickers: we often use them like this, without markers, to add geometry to an object. On the right, ordinary round markers. Until a marker is stuck on a face, the holder does not act as a marker, only as additional geometry.

Two ways of using volumetric markers

In marker mode the scanner recognises the markers and uses their relative position to determine its own position relative to the object and to merge the data. Here the holder works as a stand: inclined faces give the marker a different angle when the part surface is seen too obliquely.

In geometry mode the algorithm matches shape features on overlapping areas of the scans. No stickers are needed: the element works with its own surface, and the scanner has to capture its shape reliably.

What a volumetric marker does not do: it does not replace markers in marker mode and does not improve the accuracy of the device.
Flat markers of two diameters and two types of geometric holders around the part
Flat markers of two diameters on the table and two types of geometric holders around the part: stickers work on a flat surface, while holders give the markers inclined faces where the plane has no useful angle.

When volumetric markers help

Flat panels and large smooth surfaces

Flat stickers work on a panel as long as the cameras see them at a suitable angle. If they stop being recognised while moving around the object, some of the markers are moved onto the inclined faces of holders. In geometry mode, extra volumetric elements help on a smooth panel when the shape itself is not enough for stable registration.

The role of auxiliary geometry is easiest to see in a short video: the operator scans a small part on a turntable and lays out plasticine around it because the object lacks geometry of its own. Part of the mass is stuck right onto the surface; it will be useful when groups captured from different sides have to be merged. The algorithm gets reference points, and the person gets a chance to verify visually that the scans line up. At the end the extra geometry is removed with the standard tools of the software.

Narrow parts, ribs and edges

On a narrow surface there is often little room for stickers. Holders can be fixed on non-critical areas of the part or moved onto a common fixture, so that the mounting does not cover the edge the scan is being made for.

Small parts on the table

Markers around a small part leave the field of view as the height and tilt of the scanner change. Low holders raise part of the reference points above the table plane.

The height is chosen on site: a marker that is too tall covers the part itself. A working solution from open models is a pyramid 6 mm high with three inclined faces: flat stickers under a small part disappear as soon as the scan reaches table level, while the little pyramid stays in frame.

Cavities and hard-to-reach areas

Holders next to a cavity help keep the registration while the scanner is brought to the required area. But a volumetric marker does not guarantee visibility from every point and does not remove the limits on camera and projector access to the surface. Before the main scan, check that enough reference points remain in the working views.

Nozzle: flat markers are stuck along the inner edge, holders sit on the outer surface. This way the scanner does not lose track when it has to look deeper and catch the edge.
Nozzle: flat markers are stuck along the inner edge, holders sit on the outer surface. This way the scanner does not lose track when it has to look deeper and catch the edge.

Symmetrical parts and repeating relief

In geometry-based registration extra elements help tell similar areas apart. They are placed not in identical rows but so that the combinations of reference points differ from one another.

Example: preparing a gearbox housing

In the project of fitting a Škoda Felicia engine into a LuAZ-967 the gearbox was prepared for scanning with matting spray, magnetic and volumetric markers. The resulting data was used to align the geometry of the mating parts.

The example shows that preparation methods complement each other: matting helps capture the surface, and markers provide reference points for registration. Volumetric holders do not replace the other markers; they are part of the overall layout.

Gearbox before scanning: matting spray, magnetic and volumetric markers. The holders are outlined: they keep the tracking when the scanner moves onto the side surfaces.
Gearbox before scanning: matting spray, magnetic and volumetric markers. The holders are outlined: they keep the tracking when the scanner moves onto the side surfaces.

Requirements for the holder and for the marker itself

Compatibility with the scanner

The type and size of markers are chosen according to the equipment documentation: retroreflective stickers do not replace just any other kind. The RangeVision accessories range includes white and retroreflective markers of various diameters, self-adhesive and magnetic.

Two diameters in one project: RV 3D Studio supports markers of 3 and 6 mm within a single project, as stated among the software features on the scanner pages. Before use, check the installed software version and the marker requirements for your model.

When choosing a holder, distinguish the diameter of the marker's working area from the outer diameter of the whole sticker. The seat holds the sticker entirely, including its border, and has a 1–2 mm margin at the edge: that way nothing catches on the sticker during storage and it does not peel off ahead of time.

Markers of different diameters for 3D scanning
Markers of different diameters: the working centre is smaller than the outer diameter of the sticker, so the seat in the holder is sized by the outer contour.

Correct shape and condition of the marker

A marker must keep the shape and optical properties intended by the manufacturer. Four things matter for stable recognition:

  1. the correct shape of the retroreflective area;
  2. repeatability of that shape from marker to marker;
  3. even reflection across the whole area of the centre;
  4. contrast between the centre and the black ring: its width, matte finish and absence of glare.

Dirt, scratches, creases, peeling and deformation impair recognition. The sticker is placed on a flat spot: do not wrap it around an edge, trim the working area or stick it over noticeable irregularities.

How critical the spread across these four points is can be seen from our tests. A batch of retroreflective markers from a third-party supplier, made not by printing but by film technology, scored 3 points and landed at the level of the worst of three reference samples (5, 4 and 3 points). What was found: local deviations in the shape of the retroreflective area on some markers, uneven reflection across the area because of the grainy structure of the applied layer, and glare on the black film that eats contrast in daylight. That is film straight from the factory. A circle printed on a printer adds everything the printer does: a visible layer seam, a ragged edge, glossy black plastic and uneven fill density from part to part.

Visibility from the working directions

What matters is not the total number of stickers on the object but how many markers the scanner reliably recognises at a given moment. Aim the faces of the holders towards the expected scanner positions and check that the markers are not hidden by the part itself, neighbouring holders, the fixture or the operator's hands.

A working set of holders: markers are stuck on the faces without a repeating pattern, so some of them are visible from any scanner position.
A working set of holders: markers are stuck on the faces without a repeating pattern, so some of them are visible from any scanner position.

Staying fixed relative to the part

As long as a single reference system is used, the relative position of the part and the reference markers stays unchanged. A magnet, an adhesive pad or a clamp is suitable only if it rules out displacement under the conditions of the specific job. The general rules of placement and checking are in the article about markers.

A separate case is a turntable: the part and the external markers must rotate together. Holders on a stationary table next to a rotating part do not form a fixed reference system with it.

Surface and rigidity of the body

The body keeps its shape and holds the markers reliably. A matte surface reduces glare: a glossy body produces reflections of its own and interferes with the camera. A dark body is convenient for contrasting stickers, but colour alone does not provide recognition. If the element works by geometry, check how well the scanner captures its surface.

Repeatable jobs: a reference plate

If small parts are scanned in a similar pattern regularly, a plate with fixed markers and holders is prepared once. RV 3D Studio supports saved reference networks: a universal marker plate can be prepared in advance and reused.

The plate does not cancel the placement rules: during every pass the part keeps its position relative to the reference markers, and the reference points themselves remain accessible to the cameras. If the holders have been moved, the previous reference network cannot be considered valid for the new layout.

A home-made plate on a turntable: adhesive markers around the perimeter and two holders with markers. Such a set is made once and reused.
A home-made plate on a turntable: adhesive markers around the perimeter and two holders with markers. Such a set is made once and reused.

Buy, print or order a print

Both routes work; the choice depends on the volume of work and on how much time you are ready to spend.

Ready-made stickers and holders

Marker stickers are sold in sheets. Some manufacturers offer sets of 40 sheets: a sheet holds about a hundred 3 mm dots and half as many 6 mm ones, so a set runs to several thousand pieces. The stickers are made on PET film, and 3 mm and 6 mm sets are available on marketplaces and in scanner equipment stores.

Ready-made corner, magnetic and other holders are convenient if they fit in size, height and mounting method. The RangeVision accessory sets for handheld scanners include magnetic, corner and corner magnetic markers: magnetic bases for suitable surfaces, corner elements when the orientation of the markers has to change. Check the contents of a specific set when ordering.

Before buying, check not only marker compatibility but also the dimensions of the body. A large tower is convenient on a big panel and gets in the way when scanning a small part.

Printing it yourself

Printing lets you tailor the height, the shape of the faces, the base and the mounting to your task.

It is the holder body that can be printed. Working markers are better bought ready-made: ordinary FDM printing does not reproduce the properties of retroreflective film, and a printed contrasting pattern cannot automatically be considered a suitable marker. The reasons are in the section about the shape and condition of the marker.

When choosing a ready-made 3D model, check:

  • the outer size of the sticker the seat is made for;
  • marker accessibility for the cameras at the required angles;
  • the height and stability of the holder;
  • the mounting method;
  • whether a worn sticker can be replaced;
  • the licence terms of the model.

Do not scale a model without checking: the seats for stickers, magnets and connectors change together with the body.

Ordering a print

If you have no printer of your own, the body is ordered from a ready model. The contractor receives not only the file but also the requirements for seat dimensions, material and the quality of the sticker pads.

Lead time and cost depend on the design, the number of holders and the print settings. One base prints in about 15 minutes, so a set of 20–30 markers is a few hours of printing, not a week.

Open models and licences

There are many open models; they are free and intended for an ordinary FDM printer. Below are the ones worth taking as a starting point. Licences differ, so the file is downloaded from the author rather than re-uploaded: some models allow personal use only, and the printed parts cannot be sold.
  • A complete system by Про СМП (Printables): stands, hemispheres, mushrooms, corners — 31 files in the set. All figures have shallow recesses for 6 and 10 mm markers (8 and 12 mm recesses). All parts have holes for 5×2 mm cylindrical magnets. Licence CC BY-NC-ND: you may print for yourself if you credit the author; you may not sell the printed parts or publish a modified model.
  • Modular magnetic towers by Made.In.Meidling (MakerWorld): stands for 10 and 6 mm markers, bases for 10×2 mm magnets, parts connect to each other and assemble into a marker of the required height. There is a version with slim posts that do not block the model; the author recommends a 0.12 mm layer because of the thread. Licence Standard Digital File License (MakerWorld): personal use only, the printed parts cannot be sold.
  • Pyramid for 3 mm dots by ExactShapeSolutions (Printables): 6 mm high, three inclined faces, a slot for a 9×1 mm magnet. Designed exactly for the case where “flat markers under a small part disappear when the scan reaches the table”. Licence CC BY-NC-SA: personal use with attribution, the printed parts cannot be sold.
  • Base for standard stickers by JH (Printables): two versions, with a slot for a 10×1.5 mm magnet and without it, STEP files for edits, one part prints in about 15 minutes. Licence Public Domain: anything is allowed, including selling the printed parts.
  • “Hemisphere and pyramid” by vogonnik (3DToday): the simplest in this list, two parts, no magnets, licence CC BY — selling is allowed too, provided the author is credited. Suitable when markers are needed on the table rather than on metal.
  • Holders for 19 mm stickers by MattxD (MakerWorld): a large option with a 10×3 mm magnet in the base, printable in PLA, PETG, ASA or ABS. Licence Standard Digital File License (MakerWorld): personal use only, the printed parts cannot be sold.

For yourself you can print almost any model from the list. Selling the printed markers is allowed only under models licensed CC BY, CC BY-SA or Public Domain, with attribution. Anything marked NC (non-commercial use) or Standard Digital File License (MakerWorld) is for personal use only: such markers cannot be sold, and the file must not be re-uploaded to your own site either.

How to print and assemble a holder

  1. Choose compatible markers. Find out the size of the working area and the outer diameter of the sticker.
  2. Select or design the body: flat pads, suitable face angles, a stable base. The holder should not be taller or wider than the task needs.
  3. Check the seats. The sticker fits entirely with a 1–2 mm margin at the edge; the lips of the recess do not hide the marker from the working directions.
  4. Print the body. Use the material and settings at which the body and the joints keep their rigidity. Use a finer layer if the model has threads or small slots: in one of the open models the author recommends 0.12 mm because of steep overhangs.
  5. Prepare the pads: remove burrs, dust and dirt, degrease the bottom of the recess. Consider the compatibility of the agent with the plastic and the adhesive layer of the sticker.
  6. Fit the mounting and the magnets. If the model has a closed cavity for a magnet, it is inserted on a print pause and the following layers seal it. For modular joints, check polarity and the absence of play.
  7. Apply the markers without creases or bubbles, following the manufacturer's instructions. A self-adhesive sticker usually needs no extra glue unless the design says otherwise.
  8. Check the holder on the scanner: recognition from the working directions and no displacement during normal handling.

Magnetic markers: convenience and limits

A magnetic base allows holders to be fitted and removed quickly on steel and cast-iron surfaces. Aluminium, plastic, wood and other non-magnetic bases need a different mounting method.

What the magnet gives besides speed:

  • Fitting without glue. The holder goes on and comes off in a second, and the object needs no preparation or subsequent cleaning.
  • Mounting to the table. A steel plate, a magnetic turntable, a cast-iron bed: the marker holds itself, without clamps or tape.
  • Modularity. Parts connect to each other with magnets: a base, a post and a top assemble into a marker of the required height. Polarity is easy to set: a second magnet is snapped to the already pressed one and pushed into the mating seat, and the orientation sets itself.
  • Gluing-free assembly during printing. A pause is set in the print profile, the magnet is placed into the cavity at that moment, and the following layers seal the cavity.

Sizes from the practice of open models: 5×2 and 10×2 mm for connecting parts, 10×3 and 9×1 mm for the base, 4 mm in flat bases, 20×15×2 mm in heavy bases. The logic is simple: the taller the marker and the more it is knocked about in use, the larger the magnet.

The mere fact of attraction does not yet mean reliable fixation. A magnet pulls along the normal and does not prevent sliding along the surface, so on an inclined base the holder may creep. Check before work:

  • whether the marker shifts;
  • whether a thin part flexes when the holder is fitted;
  • whether the base interferes with scanning;
  • whether the holder can be removed without damaging the coating;
  • whether there are restrictions on using magnets near the equipment.

For scratch-sensitive surfaces, assess the protection of the base and the cleanliness of the contact area separately. A magnet that is too strong distorts a light assembly when it is fitted, and the marker then has to be pulled off with a jerk.

Magnetic markers on a car sill: the scanner captures the lower part of the door and the sill itself, where ordinary markers are almost invisible.
Magnetic markers on a car sill: the scanner captures the lower part of the door and the sill itself, where ordinary markers are almost invisible.

Can plasticine be used instead of geometric markers

Plasticine or removable adhesive putty can serve as auxiliary geometry if the scanner registers data by surface shape. A few distinct bosses help add reference points to a smooth part. The Spectrum page describes the technique directly: missing geometry can be added by placing pieces of plasticine next to the object.

But the method does not suit every job:

  • the material is not retroreflective, so in marker mode it does not replace stickers;
  • plasticine is soft and will shift on a moving, vibrating or inclined object;
  • it leaves marks on porous surfaces, untreated wood and fresh paint;
  • bosses that are too small or poorly captured give no useful geometry;
  • the elements cover part of the object.

Before use, check the compatibility of the material with the surface and the stability of the bosses. For a stationary scanner and a motionless part the technique works; for handheld marker-based scanning it does not.

Common mistakes

  • Printing the marker itself and expecting it to “work”. Film and printing give different quality of the retroreflective area; the body is printed, the marker is bought.
  • Fixing a marker with tape, in mid-air or on a moving element. The scanner treats it as stationary while it shifts, and both tracking and registration drift.
  • A magnet on an inclined surface. The magnet holds but does not prevent sliding: the marker creeps slowly, and that shows up only in the merge.
  • The holder covers an edge, a hole or a seat that is needed in the model. The surface is captured but can no longer be measured.
  • A holder that is too tall or too wide next to a small part: it blocks the object from the cameras.
  • A recess deeper than the sticker is thick, or with high lips. The marker cannot be read at an oblique view.
  • Holders were moved but the old reference network is still in use. A plate matches only the layout it was built for.

What to do about the other mistakes — regular rows of markers, glare, a part shifting relative to the markers — is covered in the article about choosing and placing markers.

Do not do this: markers are stuck in a repeating pattern, including on the rulers. Identical combinations of dots confuse the merge.
Do not do this: markers are stuck in a repeating pattern, including on the rulers. Identical combinations of dots confuse the merge.

Questions and answers about geometric markers

No. Whether they are needed depends on the mode, the shape of the object and the shooting conditions. If the scanner works reliably with flat markers or with the part's own geometry, volumetric holders may not be needed at all.

What to check before scanning

The check concerns the holders; the layout of the markers and the test pass along the route are described in the article about markers.

  • The holder does not rock, slide or turn from a light push.
  • At least one face with a marker stays visible from every working direction, verified by walking around the part in preview.
  • The holders do not cover the surface to be measured and do not block the part from the cameras.
  • The magnetic base has been checked on a slope: the marker does not creep.
  • If the part is turned over or placed on a turntable, it is clear what rotates together with it.
  • The reference plate matches the current layout.

A geometric marker is useful not by itself but as part of a thought-through scanning scheme: give the scanner accessible and stable reference points without preventing it from capturing the surface you need.

To work with RangeVision scanners you can choose ready-made markers and holders from the accessories range or make a body for your own task. Check the marker type and the working procedure in the manual for your model, and the capabilities of RV 3D Studio in the documentation and the description of the installed version.

Andrey Zyabko
Prepared by Andrey Zyabko, Business Development Manager at RangeVision
Published 3 November 2026 · Updated 19 November 2026
Read also